Command and Conquer: Renegade Official Forums: General Discussion

Home » General Discussions » General Discussion » If you know cars and engines...

Show: Today's Messages :: Polls :: Message Navigator

Re: If you know cars and engines... [message #296902 is a reply to message #296819]

Wed, 14 November 2007 13:43

light
Messages: 988
Registered: January 2005

Karma:

Colonel

nikki6ixx wrote on Wed, 14 November 2007 19:56

Rats. The link is down. He's gotten too popular.

Works for me.

Quote of original post:

Quote:

First off, Jay, stay out of this.

Ok. I didn't want to mention it but I was thinking about turbo charging my Vette. I got to thinking about it and how in efficient even turbos are (compressor efficiencies of about 80% at best).

Since a turbo's function is to pressurize incoming air and force it into the upper motor, and turbos are driven by high pressure exhaust gas created from the combustion process, couldn't I just bypass the turbo altogether and route my headers back into the throttle bodies?

Since I have CFI, I could balance the DEI (direct exhaust injection as I just coined it) by feeding one header into each throttle body. Yes, the charge air wouldn't be that cold, but it would be under a hell of a lot more pressure.

I attached a quick sketch below:

http://www.gmmodernmuscle.com/fileupload/uploads/dei.jpg

There are still a few things I need to work out:
1) How do I get the CFI aircleaner to fit in a way that hides this plumbing?
2) Does anyone make a V-band clamp that will bolt an exhaust header to a CFI throttle body?
3) What pinion angle should I use in my rear-end? I'm sure there will be a noticeable difference in torque output.

What do you guys think?

http://www.azupload.com/displayImage.php/setid2745.png

Report message to a moderator

[Message index]

		If you know cars and engines... By: nikki6ixx on Tue, 13 November 2007 22:02
		Re: If you know cars and engines... By: Oblivion165 on Tue, 13 November 2007 22:29
		Re: If you know cars and engines... By: nikki6ixx on Tue, 13 November 2007 23:56
		Re: If you know cars and engines... By: light on Wed, 14 November 2007 13:43
		Re: If you know cars and engines... By: _SSnipe_ on Wed, 14 November 2007 14:12
		Re: If you know cars and engines... By: cheesesoda on Wed, 14 November 2007 14:27
		Re: If you know cars and engines... By: Muad Dib15 on Wed, 14 November 2007 14:31
		Re: If you know cars and engines... By: cheesesoda on Wed, 14 November 2007 14:33
		Re: If you know cars and engines... By: Jerad2142 on Sun, 18 November 2007 17:17
		Re: If you know cars and engines... By: luv2pb on Wed, 14 November 2007 21:45
		Re: If you know cars and engines... By: AoBfrost on Thu, 15 November 2007 07:40
		Re: If you know cars and engines... By: luv2pb on Thu, 15 November 2007 08:04
		Re: If you know cars and engines... By: jnz on Thu, 15 November 2007 08:15
		Re: If you know cars and engines... By: Memphis on Thu, 15 November 2007 09:23
		Re: If you know cars and engines... By: Muad Dib15 on Thu, 15 November 2007 15:00
		Re: If you know cars and engines... By: nikki6ixx on Thu, 15 November 2007 15:29
		Re: If you know cars and engines... By: Memphis on Thu, 15 November 2007 15:32
		Re: If you know cars and engines... By: EvilWhiteDragon on Thu, 15 November 2007 16:26
		Re: If you know cars and engines... By: jnz on Sun, 18 November 2007 17:24
		Re: If you know cars and engines... By: trooprm02 on Fri, 16 November 2007 10:12

Previous Topic:	Test this for me, eh? PokemonCA Engine Test
Next Topic:	Announcing CNCMods.net

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Nov 16 11:36:06 MST 2025

Total time taken to generate the page: 0.00924 seconds